EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.
|Published (Last):||7 February 2014|
|PDF File Size:||14.19 Mb|
|ePub File Size:||18.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
The design of the magnetic plates is very flexible and can be adapted in size and shape for different requirements according to the user’s specification. In addition, all requirements of EN for injection moulding machines and EN for presses are met. The electric control M1C is used for small and medium-sized machines. For easy and safe mould change, roller bars with spring packs are installed below the magnetic plate. M-TECS function principle for furomap design.
Pin d2 18 — 36V DC max. An indicator light on the remote control continuously shows the state of the system.
Magnetic clamping system for a KM The electric control M2C is used for large machines. A supplied separate control in combination with the press control provides the required safety for man and machine. The forces can be adapted upwards and downwards to the needs of the machine.
All signals which are not optional shall be supported by all injection moulding machines and magnetic clamping systems. Combinations with Hilma machine vices or Stark zero point clamping systems can be easily realised, as they all come from a single supplier.
Technical Recommendations | EUROMAP – European Plastics and Rubber Machinery
Figure 8 Magnet clamping system for an injection moulding machine of the company Engel Closure force: Inquiry – checklist for a quotation: Figure 11 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products.
The fixation is made in an all around clamping groove by means of clamping claws. Clamping forces of e. Figure 9 Long pole technology in a to injection moulding machine Closure force: Clamping and unclamping of several dies at the same time within a second.
Die or mould change on punches and presses within a few minutes as well as further processing advantages are created with Hilma magnetic eromap systems. This is intended to provide interchangeability. The product range “M-TECS” stands for magnetic clamping technology, that means clamping technology of the highest level and offers the following key advantages for the user: A further supplier added v.
The technology of the magnetic clamping plates is based on the principle of an electro-permanent magnet and is thus safe, even in case of a pressure failure.
Magnetic clamping systems for deformation tools | Römheld GmbH Friedrichshütte
During the whole machining process, the control continuously monitors the parameters of the magnetic force, the position of the die die contact and the temperature. Rotary table with magnetic plate. Quick die change on presses and automatic punching machines. Functional principle and interface of the magnetic clamping system: The mains supply of the MCS is also specified.
It is suitable for fitting or retrofitting without any problems in nearly all presses. The signals are conducted from the signal source to the respective pin. There are eurmoap limits set to the geometric shape of the magnetic plates.
Pin a2 and Table 2: Size and geometric shape can be freely designed as requested by the customer. The magnetic force is generated in a very flat, highly concentrated magnetic field.
Figures 1 and 2 corrected v. For the injection moulding machine see Figure 2 and the magnetic clamping system see Figure 1 the plug contacts should be capable of taking a minimum of V and 10 A. The plate thicknesses are between 75 mm. A permanent monitoring of the clamping condition, the temperature, and the position of the die by a supplied, separate control offers the maximum possible safety for automated processes.
Safety of euroap magnetic clamping system: Figure 14 Magnetic clamping system for a vertical Arburg machine With double rotary table Clamping 770 at the top and ruromap the bottom. Only to unclamp the die, electrical energy is required again. The system consists of two electro-permanent magnetic plates, a control, a remote control, a complete set of cables and mounting takes often only a few hours.
With the smallest movement of a die half, the machine will be stopped guaranteed safety for man and machine. The mould euromp are heated by the magnetic heating plate.
All of the desired performance levels can be met. In addition recommendations are given for signal voltage and current levels.
The interface to the press is always designed redundantly, is effected via potential-free contacts to stop or drive the machine. Power is only required for about 2 seconds to magnetise clamp the system at the beginning. All signals are ehromap signals unless otherwise noted.
Plug on the injection moulding machine female.